Intel ssd toolbox windows 7 x64

ТОП-сегодня раздела «HDD утилиты»

Отзывы о программе Intel SSD Toolbox

Note: The Intel SSD Toolbox will reach End of Maintenance with no additional updates after September 2020. Intel recommends that users migrate to the Intel Memory and Storage Tool (GUI) as a replacement for Intel SSD management and firmware updates.

The Intel Solid-State Drive Toolbox (Intel SSD Toolbox) is drive management software that allows you to:

• View current drive information for Intel Solid-State Drives (Intel SSDs), including:
  • Model number, capacity, and firmware version
  • Drive health
  • Estimated drive life remaining
  • SMART attributes (also available for hard disk drives and non-Intel SSDs)
  • IDENTIFY DEVICE information (also available for hard disk drives and non-Intel SSDs)
• Optimize the performance of an Intel SSD using Trim functionality
• Optimize the performance of an Intel SSD in RAID 0 using Trim functionality Intel® Rapid Storage Technology (Intel® RST) 11.0 or greater. Note: Trim on RAID 0 is not supported on Windows 8* or Windows Server 2012
• Obtain proactive notifications of new Intel SSD Toolbox software versions for Windows 7 and Windows 8 systems
• Update the firmware on a supported Intel SSD
• Run quick and full diagnostic scans to test the read and write functionality of an Intel SSD
• Check and tune your system settings for optimal Intel SSD performance, power efficiency, and endurance
• View your system information and hardware configuration, such as central processing unit (CPU), chipset, controller name, and driver versions
• Run Secure Erase on a secondary Intel SSD

The Intel SSD Toolbox supports firmware updates on the following Intel SSDs:

• Intel Solid-State Drive 310 Series Firmware 2CV102M3
• Intel Solid-State Drive 311 Series Firmware 2CV102M5
• Intel Solid-State Drive 320 Series Firmware 4PC10362
• Intel Solid-State Drive 330 Series Firmware 300i
• Intel Solid-State Drive 335 Series Firmware 335u
• Intel Solid-State Drive 510 Series Firmware PPG2 or PPG4 (120GB SSD)
• Intel Solid-State Drive 510 Series Firmware PWG2 or PWG4 (250GB SSD)
• Intel Solid-State Drive 520 Series Firmware 400i
• Intel Solid-State Drive 530 Series Firmware DC12
• Intel Solid-State Drive 710 Series Firmware 6PB10362
• Intel X18-M / X25-M SATA SSDs (34nm) Firmware 2CV102M3
• Intel X18-M / X25-M SATA SSDs (50nm) Firmware 8820
• Intel X25-E SATA SSDs Firmware 8850
• Intel X25-V SATA SSD Firmware 2CV102M3
• Intel Solid-State Drive DC S3500 Firmware 0355
• Intel Solid-State Drive DC S3700 Firmware 0265

Installation Instructions:

1. Copy the file TurboBoostSetup.exe to your system.
2. Double click on TurboBoostSetup.exe. Accept the UAC prompt, if one appears.
3. Follow the installer prompt instructions to complete installation.
4. If installing on the Windows Vista operating system, double click the ‘Intel® Turbo Boost Technology Monitor’ gadget in the gadget gallery that pops up to install the gadget to the Windows Sidebar. This is automatically done on Windows 7

What’s New:

This tool version contains fix for the following issue:

• Fix for system crash that may occur under certain conditions when running
• performance booster

This release of Intel® SSD Toolbox includes the following updates for Intel® Optane™ Solid State Drive 905P/900P Series:

• Fix for drive fails to set correct Native Max LBA when forcing max ddress capacity to smaller one
• Fix for media errors + E2E error increments after coming back to the native capacity
• Fix for drive sometimes fails PCIe training during reboots resulting in reduced link width or speed
• Fix Link width degrades during link disable/enable on some platforms
• Fix for Serial number is all zeroes after U.2 drive hotplug operation
• Fix for Quality Reliability Test encountered Cold ECC Failure
• Addresses CVE-2020-0584, CVE-2020-12309, CVE-2020-12310 and CVE-202012311

This release of Intel® SSD Toolbox includes the following updates for Intel® Solid State Drive Pro 7600p Series, 760p Series and E 6100p Series

• Fixes SSD FW hang seen during D3 entry for Windows Modern Standby that may cause system timeout
• Improves power during D3 state for Windows Modern Standby
• Fixes SSD DRAM training error during FW boot that may cause system timeout during device low power resume
• Fixes stability of SSD during system boot causing occasional system timeout
• Addresses CVE-2020-0584, CVE-2020-12309, CVE-2020-12310 and CVE-202012311

This release of Intel® SSD Toolbox includes the following updates for Intel® Solid State Drive 660p Series:

• Fixes SSD FW hang seen during D3 entry for Windows Modern Standby that may cause system timeout
• Improves power during D3 state for Windows Modern Standby
• Fixes for drive NDA during heavy workload that may cause system timeout
• Fixes for FW hang cause by host request for device wake up when device transitioning between low power states
• Addresses CVE-2020-0584, CVE-2020-12309, CVE-2020-12310 and CVE-202012311

This release of Intel® SSD Toolbox includes the following updates for Intel® Solid State Drive Pro 5400s Series:

• Optimizations for NAND data refresh algorithms
• Addresses CVE-2020-0584, CVE-2020-12309, CVE-2020-12310 and CVE-202012311
• This release of Intel® SSD Toolbox includes the following updates for Intel® Solid State
• Drive 540s Series and E 5400s Series
• Optimizations for NAND data refresh algorithms

This release of Intel® SSD Toolbox includes the following updates for Intel® Solid State Drive Pro 5450s Series, E 5100s Series and Pro 6000p Series:

• Addresses CVE-2020-0584, CVE-2020-12309, CVE-2020-12310 and CVE-202012311

Fast servers and clean downloads. Tested on TechSpot Labs. Here’s why you can trust us.

Обновлено

2018-10-27 16:42:47

Совместимость

Windows 7, Windows 8, Windows 10

Сайт

downloadcenter.intel.com

Intel Solid-State Drive Toolbox Программа для диагностики и оптимизации SSD-дисков от компании Intel, которая поможет следить за состоянием накопителя, тестировать его и обслуживать. Она автоматически определяет все подключенные диски (в т.ч. от других производителей) и показывает подробную информацию о каждом из них (модель, объем, версию прошивки, серийный номер и пр.).

В добавок к этому, показывается информация о каждом секторе, общие параметры диска, поддерживаемые режимы передачи, размер кэша, скорость чтения/записи и пр. Основываясь на собранных S.M.A.R.T. данных, программа также может оценить состояние диска, и определить примерный оставшийся срок работы.

Помимо предоставления технической информации о диске,
Intel Solid-State Drive Toolbox может проводить быстрое или полное диагностическое сканирование, чтобы оценить производительность при чтении/записи данных. Первый режим сканирования анализирует только 1.5 Гб дискового пространства, в то время как второй проверяет на ошибки и ищет битые сектора по всему диску.

Данную программу можно использовать для полной очистки SSD-диска, обновления прошивки и оптимизации диска для повышения производительности.

Intel Solid-State Drive Toolbox это весьма полезный инструмент для всех владельцев SSD дисков от компании Intel.