Unidentified network windows 10 как исправить

Сейчас практически у каждого пользователя есть доступ к интернету. Некоторые используют проводное соединение, а другие сидят через Wi-Fi. Тип подключения совсем не важен, каждый может столкнуться с появлением ошибки «Неопознанная сеть» на устройствах под управлением операционной системы Windows 10. В таком случае соединение будет ограничено и не получится открыть ни один сайт. Дело в том, что неполадка возникает еще на стадии попытки соединения, поэтому сразу же возникает несколько очевидных методов ее решения, о которых и пойдет речь в нашей статье.

Иногда рассматриваемая проблема появляется сама по себе, что связано с неполадками со стороны провайдера, поэтому есть смысл подождать немного в надежде на ее самостоятельное исправление. Если спустя время никакого эффекта не наблюдается, советуем для начала обратить внимание на самые банальные советы, которые достаточно часто оказываются действенными:

• При появлении ошибки после выполнения каких-либо действий, например, изменения настроек сети или установки программы, попробуйте вернуть все на свои места. Когда самостоятельно это сделать не получается, восстановите состояние доступным стандартным методом. Детальное руководство на эту тему ищите в отдельных материалах по следующим ссылкам.

Подробнее:
Восстанавливаем ОС Windows 10 к исходному состоянию
Откат к точке восстановления в Windows 10

• При использовании модема проблема может заключаться именно в нем. Часто помогает стандартная перезагрузка, ведь она приводит к освобождению памяти Wi-Fi роутера и обнулению его состояния. Такая же процедура относится и к компьютеру: через «Пуск» выберите пункт «Перезагрузка» и дождитесь включения.

Подробнее: Перезагрузка роутера

• Попробуйте отключить установленный антивирус, если такой имеется. Обычно это помогает при появлении надписи «Нет подключения к Интернету, защищено».

Подробнее: Отключение антивируса

• При использовании прямого подключения кабеля от провайдера в компьютер или ноутбук позвоните поставщику интернет-услуг и уточните, не возникло ли каких-то сбоев на линии или не ведутся ли сейчас ремонтные работы. Ведь нельзя исключать тот факт, что неисправности бывают не только со стороны юзера, но и провайдера.

Если ничего из перечисленного выше не принесло никакого результата, советуем перейти к осуществлению более сложных способов. Мы постараемся максимально детально и просто рассказать о каждом, начиная с самого элементарного.

Способ 1: Сброс настроек сети

Один из самых простых и действенных методов — сброс сетевых настроек. Иногда пользователь случайно или намеренно изменяет настройки подключения, что приводит к появлению различных проблем. Помимо этого, конфигурация могла быть изменена под действием программного обеспечения или после инсталляции обновлений. Сброс их до первоначального вида производится буквально в несколько кликов.

1. Откройте меню «Пуск» и перейдите в «Параметры».



2. Выберите категорию «Сеть и Интернет».



3. Перейдите в раздел «Состояние» и щелкните по ссылке «Сброс сети».



4. Вы будете ознакомлены с уведомлением о действии этой процедуры. Ознакомившись со всеми нюансами, кликните на «Сбросить сейчас» и ожидайте перезагрузки ПК.

Точно такие же действия доступны к выполнению и через «Командную строку». Для некоторых юзеров такой вариант покажется удобнее, ведь всего-то требуется запустить консоль через меню.

Далее по очереди введите в нее такие команды:

netsh int ip reset
ipconfig /release
ipconfig /renew

По завершении отправьте компьютер на перезагрузку и попробуйте заново произвести соединение.

Способ 2: Средство устранения неполадок

В операционной системе Виндовс 10 присутствует ряд утилит, позволяющих автоматически исправить часто возникающие проблемы. Среди них присутствует и инструмент по диагностике и наладке работы сети. Находится он в разделе «Обновление и безопасность» в меню «Параметры».

Слева имеется меню, где требуется выбрать «Устранение неполадок», а затем «Подключения к Интернету». Это запустит сканирование.

Придется подождать некоторое количество времени, пока средство устранения неполадок завершит сканирование и исправление. Возможно, на экране отобразятся дополнительные инструкции, которые нужно точно выполнить.

Довольно часто стандартная утилита позволяет решить возникшую трудность, поэтому не стоит пренебрегать этим методом, ведь это может сэкономить нервы и силы, которые были бы потрачены на поиск и исправление ошибки «Неопознанная сеть».

Способ 3: Изменение сетевых настроек

Если вы столкнулись с рассматриваемой сегодня ошибкой, следует знать, что она означает невозможность компьютера получить IP-адрес от сетевого оборудования. Это может быть связано с неправильной конфигурацией сетевого протокола IPv4 или проблемами с работой DHCP-сервера, который и задействован для получения настроек сети. Рекомендуется самостоятельно проверить текущую конфигурацию и попробовать изменить ее для нормализации подключения.

1. Через уже знакомое меню «Параметры» перейдите в «Сеть и Интернет».



2. Откройте пункт «Состояние» и щелкните ЛКМ по ссылке «Изменить свойства подключения».



3. Опуститесь вниз и в разделе «Параметры IP» нажмите на кнопку «Редактировать».



4. Если выставлены ручные значения, измените тип на «Автоматически (DHCP)» и кликните на «Сохранить».



5. В случае обнаружения уже и так использующейся автоматической конфигурации, следует изменить ее на статическую, выбрав режим «Вручную» и активировав «IPv4».



6. Узнайте IP-адрес своего оборудования (обычно он пишется на корпусе роутера и имеет вид 192.168.1.1). В строке «IP-адрес» введите полученное значение, изменив только последнюю цифру на любую другую, например, 2. Пропустите следующий пункт, он заполнится автоматически, а в качестве «Шлюз» укажите адрес маршрутизатора. В «Предпочтительный DNS-сервер» и «Дополнительный DNS-сервер» введите 8.8.8.8 и 8.8.4.4. По окончании конфигурации проверьте указанные данные и сохраните изменения.

Способ 4: Настройка параметров локальной сети

Выше мы разобрали три самых эффективных метода, которые помогают в большинстве ситуаций. Теперь мы хотим поговорить о дополнительных вариантах. Они тоже оказываются полезными, но реже. Начать бы хотелось с изменений параметров локальной сети. Для этого нужно перейти в «Свойства браузера» через классическое приложение «Панель управления».

В свойствах откройте вкладку «Подключения» и выберите «Настройка сети».

Здесь остается только поставить или снять галочку возле «Автоматическое определение параметров», что зависит от текущей настройки.

После изменений выполните переподключение к сети, чтобы обновить конфигурацию, и проверьте, какой результат будет сейчас.

Способ 5: Переустановка или обновление сетевого драйвера

За совместимость с сетевым оборудованием отвечает специальный драйвер. Если версия программного обеспечения устарела или была установлена некорректно, могут возникнуть проблемы с подключением. Тогда юзеру придется самостоятельно удалять драйвер и добавлять его в систему заново, используя новую версию или старую, но скачанную из официального сайта. Деинсталляция компонентов доступна прямо из Диспетчера устройств либо при помощи специального софта, с которым вы можете ознакомиться в отдельной статье далее.

Подробнее: Программы для удаления драйверов

После успешного удаления драйвер требуется поставить повторно. Делается это разными методами, каждый из которых подойдет в определенной ситуации. Другой наш автор максимально детально расписал каждый способ в материале, который вы найдете ниже.

Подробнее: Поиск и инсталляция драйвера для сетевой карты

Способ 6: Изменение плана электропитания

От плана электропитания зависит не только производительность устройства, но и работа определенных функций. Иногда снижение потребления энергии негативно сказывается на работе сетевого подключения. Поэтому мы рекомендуем убедиться в том, что системные настройки выставлены в значение «Максимальная производительность». Только тогда можно будет исключить фактор вины этого параметра.

Подробнее: Смена плана электропитания Windows 10

На этом наша статья подходит к своему логическому завершению. Выше вы были ознакомлены с шестью методами решения рассмотренной проблемы. Мы постарались их расставить по мере эффективности, поэтому при выполнении каждого из них по порядку вы получаете максимально большой шанс попасть на подходящий способ.

We use the Internet on daily basis, and it’s a major problem for many users if they can’t access it. Many of our readers reported Unidentified network or Unidentified network no Internet messages on their PCs, and today we’re going to show you how to fix that problem.

Whether it’s happening on your Ethernet or Wi-Fi connection, our solutions will cover all the possible issues that cause these errors on Windows 10 and Windows 11.

But first, let’s go through some preliminary methods of troubleshooting some of the main disruptions that may occur.

What causes the Unidentified Network issue?

Before getting to any solutions listed below, let’s verify some of the most common problems that may cause Internet connection errors:

➡ Check all local networking components

Several users reported that this issue occurs due to the Ethernet cable. One workaround that might help is to unplug and reconnect your Ethernet cable from your PC and router or modem.

Repeat the process several times and check if that solves the problem. In addition, be sure to check your Ethernet cable. If your Ethernet cable is damaged, you might encounter this message.

To fix the problem, you should try replacing your cable. We have a list including the best Cat6 and Cat5E cables that you can choose from.

Restarting and resetting your router and/or modem can also fix this problem quickly and you will see how you can do that in one of our solutions below.

➡ Make sure you are close to your Wi-Fi hotspot

If these errors occur while your device is connected to a Wi-Fi hotspot, make sure that you have enough signal strength.

Move your device closer to the router and eliminate all possible obstacles between the two devices.

That being said, you can start troubleshooting the problems, step by step, as shown below. It’s important to follow the exact procedures in order to fix the errors.

How do I fix the Unidentified network error in Windows 10?

1. Turn off Airplane mode

1. Press Windows key + A to open Action Center, then click the Airplane mode icon to disable the feature.
2. If this option isn’t available, press the Windows key and select Settings.
3. Go to Network & Internet section.
4. Navigate to Airplane mode tab, locate the Airplane mode option and turn it off.

Windows 10 supports Airplane mode, but if you turn on this feature, it will block your Internet connection.

You can also use a hardware switch on your device to turn off Airplane mode. Many devices have this button available, so be sure to look for it on your device.

If you encounter other problems, check our guide on how to fix Airplane mode errors and get more information.

After disabling Airplane mode using the aforementioned methods, Unidentified network message should hopefully disappear.

2. Remove your antivirus software

1. Open the Settings app by clicking on the Start icon and selecting it from the list.
2. Click on Apps from the Home menu in Settings.
3. The list of installed applications will appear on the right pane. Select the antivirus program from the list and click on the Uninstall button.
4. After the antivirus is removed, restart your PC and see if the problem has been solved.

Antivirus software is one of the most important tools that you can have on your PC and it’s paramount for system protection.

However, some antiviruses can sometimes interfere with your network connection and cause Unidentified network message to appear.

Users reported that the cause for this problem was Avast, and in order to fix the issue you need to remove it completely.

Should you have another antivirus installed, you can start by disabling first and check if the Internet connection is fixed.

If uninstalling your antivirus software fixes the problem, you need to update your antivirus software to the latest version. Alternatively, you can switch to a better antivirus tool.

3. Update network card drivers

1. Press the Start icon, type device manager and select the app from the results.
2. Locate the Network adapters section, click on it to expand, then right click on your network adapter and choose Update driver from the menu.
3. Click on Search automatically for updated driver software option and wait while Windows 10 downloads the suitable driver for your network adapter.

If you’re getting Unidentified network message, you might have to update your network drivers to fix this issue.

Although Device Manager allows you to update your drivers easily, sometimes it’s better to download the necessary drivers from your network adapter manufacturer.

For that, visit your network adapter manufacturer’s website or the device manufacturer website and locate the drivers section.

Select your network adapter from the list, download the suitable driver and install it. If you don’t have Internet access at all, you’ll need to use a working computer or any other device to download the drivers.

In order to prevent PC damage by installing the wrong driver versions, we suggest doing it automatically by using a specialized tool like DriverFix.

The software below will do all the job on your behalf by updating the correct version of drivers for your device.

4. Turn off Fast Startup

1. Click the Start button, type power and sleep, and select Power & sleep settings from the results.
2. When Power Options window opens, click on Choose what the power buttons do.
3. Now click on Change settings that are currently unavailable.
4. Uncheck Turn on fast startup, then click on Save changes.
5. After doing that, shut down your PC. Wait for 30 seconds and turn it back on again.

Windows 10 uses the Fast Startup feature by default that allows you to boot Windows 10 faster. It’s very useful, but it doesn’t completely shut down your PC, which can lead to certain issues.

To fix the ethernet unidentified network issue on your PC, many users are recommending to temporarily disable this feature.

Users reported that disabling Fast Startup fixed the problem for them, so be sure to try that. In fact, if this solution worked, you could enable it again and check if the issue reappears.

7. Restart your PC

1. Press the Start icon, click on the Power button, then select Restart from the menu.

According to users, sometimes you can fix this problem simply by restarting your PC.

It seems that Windows 10 can sometimes hold your personal files, and that can cause Unidentified network message to appear.

8. Reset the Internet settings using Command Prompt

8.1 Use the ipconfig commands

1. Press the Start button, type cmd, and select Run as administrator from the results.
2. Type or paste the following commands and press Enter to run them:
   • ipconfig /release
ipconfig /renew
3. After the commands are executed, close Command Prompt and check if the issue is resolved.

8.2 Reset winsock

Several readers reported that they fixed the issue using different set of commands. Instead of commands that we used in Step 2, use the following commands:

netsh winsock reset
netsh int ip reset
ipconfig /flushdns

8.2 Use the netsh commands

There’s also another set of commands that might fix the issue. According to our readers, you can fix Unidentified network message simply by running these commands in Command Prompt:

netsh int tcp set heuristics disabled
netsh int tcp set global autotuninglevel=disabled
netsh int tcp set global rss=enabled
netsh int tcp show global

After the commands are executed, restart your PC and check if the issue is resolved.

9. Make sure that DHCP is enabled

1. Right-click the Start icon and select Network Connections.
2. Choose Ethernet from the left, then click on Change adapter options from the right.
3. Locate your network connection, right click it and choose Diagnose from the menu.

A few of our readers reported that you can fix this problem by diagnosing your network. This is rather simple, and you can do it right from Network Connections window.

However, the Unidentified network message might appear if you don’t have DHCP enabled on your router. To fix the problem you need to open your router settings and enable DHCP again.

If you don’t know how to do that, be sure to check your router’s instruction manual.

10. Disable and enable your network connection

1. Right-click the Start icon and select Network Connections.
2. Select the Ethernet option from the left pane, then click on Change adapter options from the right.
3. Locate your current connection, right click it and choose Disable from the menu.
4. After disabling the connection, wait for few seconds. Right click your connection and choose Enable from the menu.

Sometimes you can fix Unidentified error message simply by disabling and reenabling your network connection.

If that doesn’t work, you might want to try disabling and enabling your network adapter. We explained briefly how to do that in Solution 13, so be sure to check it out.

11. Set a static IP address

1. Right-click the Start icon and select Network Connections.
2. Select Ethernet from the left pane andclick on Change adapter options from the right pane menu.
3. Locate your network connection, right click it and choose Properties.
4. Select Internet Protocol Version 4 (TCP/IPv4) and click on Properties button.
5. Now select the Use the following IP address option and enter the desired IP address as well as additional information. If you’re not sure about other values such as Subnet mask, Default gateway and Preferred DNS server, you can find them with a simple trick. Simply check the properties of the network connection on any device that is connected to your network and copy the necessary values.
6. After you’re done, click OK to save the changes.

According to users, this issue can occur if your IP address isn’t set to static. To fix the problem you need to change your network connection settings and enter the desired IP address manually.

There are several cases in which users fixed the problem simply by using Obtain an IP address automatically option. If you’re using a static IP address, be sure to try this option instead.

12. Use an external adapter

1. Press the Start icon, type device manager and select the app from the results.
2. Go to the Network adapters section and locate your adapter.
3. Right click the adapter and choose Disable device from the menu.
4. Restart your PC and the system will detect the correct driver. If this doesn’t work, repeat the process to reenable the device.

If you have problems with your network adapter, you might be able to fix them simply by replacing the adapter.

Several users reported that the issue was caused by an internal adapter that isn’t fully compatible with the router.

If you have the same problem, you might want to get a USB network adapter and try using it instead.

Before you can use an external adapter, we strongly suggest that you disable your internal network adapter by following the steps above.

13. Change your adapter’s duplex

1. Right-click the Windows Start button and select Network Connections.
2. Select Ethernet from the left pane and click on Change adapter options from the right pane menu.
3. Right click on your network connection and click on Properties.
4. When Properties window opens, click on Configure.
5. Go to the Advanced tab. From the Property list select Speed / duplex settings. Now change the Value to Auto Negotiation.
6. After you’re done, click OK to save the changes. Depending on your network adapter and router, you might have to use different values sometimes in order to fix the problem.

Sometimes Unidentified network message can appear if your duplex isn’t properly configured. After changing the duplex speed, be sure to check if the problem is resolved.

14. Disable McAfee Network Agent

1. Press Windows key + R, type msconfig and press Enter or click OK.
2. Go to Services tab, check the box for Hide all Microsoft services. Locate McAfee Network Agent on the list and disable it.
3. Now click Apply and OK to save the changes. In addition to McAfee Network Agent, users are also suggesting disabling McAfee Firewall Core.

As we previously mentioned, third-party applications can sometimes interfere with your network connection and cause Unidentified network message to appear.

Several users reported that McAfee Network Agent caused this issue on their PC. In order to fix the problem, you need to disable this service.

After disabling the problematic services, the issue should be resolved completely.

15. Restart your modem and router

The Unidentified network message can prevent you from accessing the Internet, but you can fix it easily by restarting your router and modem.

Sometimes your network configuration might not be correct, and a quick restart can usually solve that. To restart your modem / router, simply press its reset button and wait for 30 seconds.

After that, turn the device back on again and wait until it starts. If you have both modem and router, be sure to restart both devices.

Sometimes this error appears due to your router’s configuration. A few users reported that they successfully fixed the issue simply by resetting their router.

To do that, find and press the reset button on your router. Alternatively, you can open the router’s configuration page and reset it from there.

Keep in mind that resetting the router will revert all your settings to default, so you’ll have to set up a wireless connection and configure all your settings again.

16. Upgrade router firmware

1. Make sure that the router and PC are connected.
2. Open a browser window and enter the address of your router. The one in our screenshot is only an example. You will find that on your router manual or on the device itself.
3. Log into the app with the username and password provided.
4. Locate the firmware update option and check for updates.

If you’re getting the Unidentified network no internet access Windows 10 or Windows 11 message, you might be able to fix it by upgrading your router firmware. By updating router firmware you can fix many compatibility and security issues with your router.

We have to mention that the firmware upgrade process comes with certain risks, so if you’re not careful you can cause permanent damage to your router.

To avoid any problems be sure to check your instruction manual thoroughly before performing the upgrade.

If you need more information about firmware upgrade, be sure to check our guide on how to upgrade your router firmware for some tips.

17. Use only one network connection

1. Right-click the Windows Start icon and select Network Connections from the list.
2. Select Ethernet from the left pane and click on Change adapter options from the right pane.
3. Now select your wireless and Ethernet connection. Right click them and choose Bridge Connections from the menu.

The Unidentified network message can appear if you’re using both Ethernet and wireless connections at the same time. If that’s the case, you’ll need to disable one connection and restart your PC.

For detailed instructions on how to disable your network connection be sure to check Solution 10. After disabling Ethernet or wireless connection, restart your PC and check if that solves the issue.

If that doesn’t work, you’ll need to bridge your connections just as it’s shown in our solution above. After bridging the connections, check if the problem is resolved.

18. Check your network connection properties

1. Once again, right-click the Start button and select Network Connections from the list.
2. Select Ethernet from the left pane and choose Change adapter options from the right.
3. Now select your connection, right-click it and choose Properties from the menu.
4. Now, uninstall any options that are related to third-party applications. After you’re done, click OK to save changes.
5. Restart your computer and check if the problem is resolved.

Third-party applications can sometimes cause problems with your network connection.

some of our readers reported issues with the Shrewsoft applications, so if you see any Shrewsoft entries on the list, be sure to uninstall them.

It’s worth mentioning that other third-party applications can cause this problem, so you might have to remove them as well.

19. Disable virtual network adapters

1. Press the Start button and type device manager, then click on the app from the results.
2. Go to View menu and check Show hidden devices.
3. Now expand the Network adapters section and locate any virtual adapters associated with third-party applications. Disable those adapters and check if that solves the issue.

If you’re using any virtualization software, such as VMWare or VirtualBox, you can sometimes cause issues with your network connection.

Users reported that virtual machine software can cause the Unidentified network message by creating virtual network adapters.

To fix the problem, you need to disable virtual adapters from Device Manager. Disabling third-party virtual adapters can affect the Internet connectivity in those apps, so keep that in mind.

20. Change startup type for Bonjour service

1. Press Windows key + R and type services.msc, then press Enter or click OK.
2. When the Services window opens, locate the Bonjour service on the list and double click it.
3. Change the Startup type to Automatic (Delayed Start) and click Apply and OK to save the changes.

According to users, the Bonjour service can cause internet issues and the Unidentified network message to appear.

To fix this problem, you just need to change the startup type of the Bonjour service as shown above.

Several users reported that Id_String2.6844F930_1628_4223_B5CC_5BB94B87 9762 service can also cause this problem.

To fix the problem, simply locate the service, double-click it, and set its Startup Type to Disabled. After doing that, be sure to check if the issue is resolved.

21. Delete the 0.0.0.0 gateway

1. Click the Windows Start button, type cmd and select Run as administrator from the results to start Command Prompt with full privileges.
2. Now, type or paste the following command and press Enter to run it: route delete 0.0.0.0
3. After the command is executed, restart your PC and check if the problem is resolved.

Several users reported that the issue is caused by the 0.0.0.0 gateway courtesy of Adobe CS3 Bonjour, but you can fix the issue simply by removing the gateway.

22. Change the Power Management settings for your adapter

1. Open the Network Connections window by right-clicking the Start icon and selecting the option from the menu.
2. Click on Wi-Fi from the left, then scroll down on the right and select Change adapter options.
3. Locate your wireless connection, right-click it and choose Properties from the menu.
4. Click on the Configure button.
5. Now navigate to the Power Management tab and uncheck Allow the computer to turn off this device to save power. Click OK to save changes.
6. Right click the wireless adapter again and choose Properties.
7. Go to the Sharing tab and uncheck Allow other network users to connect through this computer’s Internet connection option. Click OK to save changes.

If you’re getting the Unidentified network message while using a Wi-Fi network, you might be able to solve it by using this method.

According to users, you can fix this problem with ease simply by changing Power Management settings of your adapter.

After making the aforementioned changes, the problem should be completely resolved.

23. Change your Roaming Sensitivity

1. Right-click the Windows Start button and choose Network Connections from the menu.
2. Click on Wi-Fi from the left pane, then scroll down on the right and select Change adapter options from Related settings.
3. Find your wireless connection, right-click it and select Properties.
4. Hit the Configure button.
5. Navigate to the Advanced tab, locate Roaming Sensitivity or Roaming Aggressiveness (depending on your system) on the list and select it, then adjust values until the problem is resolved.

A few users reported that you can fix the problem simply by disabling Roaming Sensitivity, so be sure to try that as well.

24. Change your router’s encryption

Wi-Fi networks usually use encryption in order to prevent unauthorized access. Some of our readers reported that they fixed the problem simply by changing the network encryption on their router.

Users reported issues while using WPA2 encryption, but after changing it to WPA, the issue was resolved. To see how to change the encryption type on your router, we advise you to check its instruction manual.

Usually, you will find the option in the Wi-Fi settings section under the Security section but that depends on your router brand, model, and software.

We also have a Wi-Fi and connectivity issues guide for Windows 10/11 that will further help you fix all kinds of connection problems so make sure to check it out.

25. Enter your MAC address manually

1. Click the Start button, type cmd and choose Run as administrator from the results to start Command Prompt with administrator privileges.
2. Type or paste the following command and press the Enter key to run it: ipconfig /all
3. Locate Physical Address of your adapter and write it down. The address will consist of six pairs of characters separated by dashes.
4. Now go to Network Connections window, right click your connection and choose Properties, then click the Configure button as shown in the previous solutions.
5. Go to the Advanced tab and select Network Address option from the list. Enter your MAC address in the Value field without any dashes. After you’re done, click OK button to save the changes.

If you’re getting the Unidentified network no Internet message, you might be able to fix it simply by entering your MAC address manually.

How do I fix Ethernet unidentified network in Windows 11?

Although it has some new features and design, Windows 11 is not all that different from Windows 10 and our readers have encountered all sorts of Internet connection problems in the new OS.

The Ethernet unidentified network and Unidentified network no Internet errors in Windows 11 are just as common because they are caused by the same problems.

Luckily, the similarities between the two systems will help you solve these problems by applying all the solutions we presented for Windows 10 above on the new OS.

There are, of course, a few differences. For instance, in Windows 11 is a lot easier to access the Advanced network settings from the Network & internet section in Settings.

However, should you require further information, check our guide on what you can do if you can’t connect to the network in Windows 11. It will help with Internet connectivity problems.

The Unidentified network message can prevent you from accessing the Internet, but you should be able to easily fix the problem by using some of our solutions listed above. We hope they helped!

If you switched to the new OS, we can also help you with a fix if the Windows 11 Ethernet is not working that will provide a lot more information.

Should you have more questions or suggestions for additional solutions, don’t hesitate to write us in the comments section below.

We use the Internet on daily basis, and it’s a major problem for many users if they can’t access it. Many of our readers reported Unidentified network or Unidentified network no Internet messages on their PCs, and today we’re going to show you how to fix that problem.

Whether it’s happening on your Ethernet or Wi-Fi connection, our solutions will cover all the possible issues that cause these errors on Windows 10 and Windows 11.

But first, let’s go through some preliminary methods of troubleshooting some of the main disruptions that may occur.

What causes the Unidentified Network issue?

Before getting to any solutions listed below, let’s verify some of the most common problems that may cause Internet connection errors:

➡ Check all local networking components

Several users reported that this issue occurs due to the Ethernet cable. One workaround that might help is to unplug and reconnect your Ethernet cable from your PC and router or modem.

Repeat the process several times and check if that solves the problem. In addition, be sure to check your Ethernet cable. If your Ethernet cable is damaged, you might encounter this message.

To fix the problem, you should try replacing your cable. We have a list including the best Cat6 and Cat5E cables that you can choose from.

Restarting and resetting your router and/or modem can also fix this problem quickly and you will see how you can do that in one of our solutions below.

➡ Make sure you are close to your Wi-Fi hotspot

If these errors occur while your device is connected to a Wi-Fi hotspot, make sure that you have enough signal strength.

Move your device closer to the router and eliminate all possible obstacles between the two devices.

That being said, you can start troubleshooting the problems, step by step, as shown below. It’s important to follow the exact procedures in order to fix the errors.

How do I fix the Unidentified network error in Windows 10?

1. Turn off Airplane mode

1. Press Windows key + A to open Action Center, then click the Airplane mode icon to disable the feature.
2. If this option isn’t available, press the Windows key and select Settings.
3. Go to Network & Internet section.
4. Navigate to Airplane mode tab, locate the Airplane mode option and turn it off.

Windows 10 supports Airplane mode, but if you turn on this feature, it will block your Internet connection.

You can also use a hardware switch on your device to turn off Airplane mode. Many devices have this button available, so be sure to look for it on your device.

If you encounter other problems, check our guide on how to fix Airplane mode errors and get more information.

After disabling Airplane mode using the aforementioned methods, Unidentified network message should hopefully disappear.

2. Remove your antivirus software

1. Open the Settings app by clicking on the Start icon and selecting it from the list.
2. Click on Apps from the Home menu in Settings.
3. The list of installed applications will appear on the right pane. Select the antivirus program from the list and click on the Uninstall button.
4. After the antivirus is removed, restart your PC and see if the problem has been solved.

Antivirus software is one of the most important tools that you can have on your PC and it’s paramount for system protection.

However, some antiviruses can sometimes interfere with your network connection and cause Unidentified network message to appear.

Users reported that the cause for this problem was Avast, and in order to fix the issue you need to remove it completely.

Should you have another antivirus installed, you can start by disabling first and check if the Internet connection is fixed.

If uninstalling your antivirus software fixes the problem, you need to update your antivirus software to the latest version. Alternatively, you can switch to a better antivirus tool.

3. Update network card drivers

1. Press the Start icon, type device manager and select the app from the results.
2. Locate the Network adapters section, click on it to expand, then right click on your network adapter and choose Update driver from the menu.
3. Click on Search automatically for updated driver software option and wait while Windows 10 downloads the suitable driver for your network adapter.

If you’re getting Unidentified network message, you might have to update your network drivers to fix this issue.

Although Device Manager allows you to update your drivers easily, sometimes it’s better to download the necessary drivers from your network adapter manufacturer.

For that, visit your network adapter manufacturer’s website or the device manufacturer website and locate the drivers section.

Select your network adapter from the list, download the suitable driver and install it. If you don’t have Internet access at all, you’ll need to use a working computer or any other device to download the drivers.

In order to prevent PC damage by installing the wrong driver versions, we suggest doing it automatically by using a specialized tool like DriverFix.

The software below will do all the job on your behalf by updating the correct version of drivers for your device.

4. Turn off Fast Startup

1. Click the Start button, type power and sleep, and select Power & sleep settings from the results.
2. When Power Options window opens, click on Choose what the power buttons do.
3. Now click on Change settings that are currently unavailable.
4. Uncheck Turn on fast startup, then click on Save changes.
5. After doing that, shut down your PC. Wait for 30 seconds and turn it back on again.

Windows 10 uses the Fast Startup feature by default that allows you to boot Windows 10 faster. It’s very useful, but it doesn’t completely shut down your PC, which can lead to certain issues.

To fix the ethernet unidentified network issue on your PC, many users are recommending to temporarily disable this feature.

Users reported that disabling Fast Startup fixed the problem for them, so be sure to try that. In fact, if this solution worked, you could enable it again and check if the issue reappears.

7. Restart your PC

1. Press the Start icon, click on the Power button, then select Restart from the menu.

According to users, sometimes you can fix this problem simply by restarting your PC.

It seems that Windows 10 can sometimes hold your personal files, and that can cause Unidentified network message to appear.

8. Reset the Internet settings using Command Prompt

8.1 Use the ipconfig commands

1. Press the Start button, type cmd, and select Run as administrator from the results.
2. Type or paste the following commands and press Enter to run them:
   • ipconfig /release
ipconfig /renew
3. After the commands are executed, close Command Prompt and check if the issue is resolved.

8.2 Reset winsock

Several readers reported that they fixed the issue using different set of commands. Instead of commands that we used in Step 2, use the following commands:

netsh winsock reset
netsh int ip reset
ipconfig /flushdns

8.2 Use the netsh commands

There’s also another set of commands that might fix the issue. According to our readers, you can fix Unidentified network message simply by running these commands in Command Prompt:

netsh int tcp set heuristics disabled
netsh int tcp set global autotuninglevel=disabled
netsh int tcp set global rss=enabled
netsh int tcp show global

After the commands are executed, restart your PC and check if the issue is resolved.

9. Make sure that DHCP is enabled

1. Right-click the Start icon and select Network Connections.
2. Choose Ethernet from the left, then click on Change adapter options from the right.
3. Locate your network connection, right click it and choose Diagnose from the menu.

A few of our readers reported that you can fix this problem by diagnosing your network. This is rather simple, and you can do it right from Network Connections window.

However, the Unidentified network message might appear if you don’t have DHCP enabled on your router. To fix the problem you need to open your router settings and enable DHCP again.

If you don’t know how to do that, be sure to check your router’s instruction manual.

10. Disable and enable your network connection

1. Right-click the Start icon and select Network Connections.
2. Select the Ethernet option from the left pane, then click on Change adapter options from the right.
3. Locate your current connection, right click it and choose Disable from the menu.
4. After disabling the connection, wait for few seconds. Right click your connection and choose Enable from the menu.

Sometimes you can fix Unidentified error message simply by disabling and reenabling your network connection.

If that doesn’t work, you might want to try disabling and enabling your network adapter. We explained briefly how to do that in Solution 13, so be sure to check it out.

11. Set a static IP address

1. Right-click the Start icon and select Network Connections.
2. Select Ethernet from the left pane andclick on Change adapter options from the right pane menu.
3. Locate your network connection, right click it and choose Properties.
4. Select Internet Protocol Version 4 (TCP/IPv4) and click on Properties button.
5. Now select the Use the following IP address option and enter the desired IP address as well as additional information. If you’re not sure about other values such as Subnet mask, Default gateway and Preferred DNS server, you can find them with a simple trick. Simply check the properties of the network connection on any device that is connected to your network and copy the necessary values.
6. After you’re done, click OK to save the changes.

According to users, this issue can occur if your IP address isn’t set to static. To fix the problem you need to change your network connection settings and enter the desired IP address manually.

There are several cases in which users fixed the problem simply by using Obtain an IP address automatically option. If you’re using a static IP address, be sure to try this option instead.

12. Use an external adapter

1. Press the Start icon, type device manager and select the app from the results.
2. Go to the Network adapters section and locate your adapter.
3. Right click the adapter and choose Disable device from the menu.
4. Restart your PC and the system will detect the correct driver. If this doesn’t work, repeat the process to reenable the device.

If you have problems with your network adapter, you might be able to fix them simply by replacing the adapter.

Several users reported that the issue was caused by an internal adapter that isn’t fully compatible with the router.

If you have the same problem, you might want to get a USB network adapter and try using it instead.

Before you can use an external adapter, we strongly suggest that you disable your internal network adapter by following the steps above.

13. Change your adapter’s duplex

1. Right-click the Windows Start button and select Network Connections.
2. Select Ethernet from the left pane and click on Change adapter options from the right pane menu.
3. Right click on your network connection and click on Properties.
4. When Properties window opens, click on Configure.
5. Go to the Advanced tab. From the Property list select Speed / duplex settings. Now change the Value to Auto Negotiation.
6. After you’re done, click OK to save the changes. Depending on your network adapter and router, you might have to use different values sometimes in order to fix the problem.

Sometimes Unidentified network message can appear if your duplex isn’t properly configured. After changing the duplex speed, be sure to check if the problem is resolved.

14. Disable McAfee Network Agent

1. Press Windows key + R, type msconfig and press Enter or click OK.
2. Go to Services tab, check the box for Hide all Microsoft services. Locate McAfee Network Agent on the list and disable it.
3. Now click Apply and OK to save the changes. In addition to McAfee Network Agent, users are also suggesting disabling McAfee Firewall Core.

As we previously mentioned, third-party applications can sometimes interfere with your network connection and cause Unidentified network message to appear.

Several users reported that McAfee Network Agent caused this issue on their PC. In order to fix the problem, you need to disable this service.

After disabling the problematic services, the issue should be resolved completely.

15. Restart your modem and router

The Unidentified network message can prevent you from accessing the Internet, but you can fix it easily by restarting your router and modem.

Sometimes your network configuration might not be correct, and a quick restart can usually solve that. To restart your modem / router, simply press its reset button and wait for 30 seconds.

After that, turn the device back on again and wait until it starts. If you have both modem and router, be sure to restart both devices.

Sometimes this error appears due to your router’s configuration. A few users reported that they successfully fixed the issue simply by resetting their router.

To do that, find and press the reset button on your router. Alternatively, you can open the router’s configuration page and reset it from there.

Keep in mind that resetting the router will revert all your settings to default, so you’ll have to set up a wireless connection and configure all your settings again.

16. Upgrade router firmware

1. Make sure that the router and PC are connected.
2. Open a browser window and enter the address of your router. The one in our screenshot is only an example. You will find that on your router manual or on the device itself.
3. Log into the app with the username and password provided.
4. Locate the firmware update option and check for updates.

If you’re getting the Unidentified network no internet access Windows 10 or Windows 11 message, you might be able to fix it by upgrading your router firmware. By updating router firmware you can fix many compatibility and security issues with your router.

We have to mention that the firmware upgrade process comes with certain risks, so if you’re not careful you can cause permanent damage to your router.

To avoid any problems be sure to check your instruction manual thoroughly before performing the upgrade.

If you need more information about firmware upgrade, be sure to check our guide on how to upgrade your router firmware for some tips.

17. Use only one network connection

1. Right-click the Windows Start icon and select Network Connections from the list.
2. Select Ethernet from the left pane and click on Change adapter options from the right pane.
3. Now select your wireless and Ethernet connection. Right click them and choose Bridge Connections from the menu.

The Unidentified network message can appear if you’re using both Ethernet and wireless connections at the same time. If that’s the case, you’ll need to disable one connection and restart your PC.

For detailed instructions on how to disable your network connection be sure to check Solution 10. After disabling Ethernet or wireless connection, restart your PC and check if that solves the issue.

If that doesn’t work, you’ll need to bridge your connections just as it’s shown in our solution above. After bridging the connections, check if the problem is resolved.

18. Check your network connection properties

1. Once again, right-click the Start button and select Network Connections from the list.
2. Select Ethernet from the left pane and choose Change adapter options from the right.
3. Now select your connection, right-click it and choose Properties from the menu.
4. Now, uninstall any options that are related to third-party applications. After you’re done, click OK to save changes.
5. Restart your computer and check if the problem is resolved.

Third-party applications can sometimes cause problems with your network connection.

some of our readers reported issues with the Shrewsoft applications, so if you see any Shrewsoft entries on the list, be sure to uninstall them.

It’s worth mentioning that other third-party applications can cause this problem, so you might have to remove them as well.

19. Disable virtual network adapters

1. Press the Start button and type device manager, then click on the app from the results.
2. Go to View menu and check Show hidden devices.
3. Now expand the Network adapters section and locate any virtual adapters associated with third-party applications. Disable those adapters and check if that solves the issue.

If you’re using any virtualization software, such as VMWare or VirtualBox, you can sometimes cause issues with your network connection.

Users reported that virtual machine software can cause the Unidentified network message by creating virtual network adapters.

To fix the problem, you need to disable virtual adapters from Device Manager. Disabling third-party virtual adapters can affect the Internet connectivity in those apps, so keep that in mind.

20. Change startup type for Bonjour service

1. Press Windows key + R and type services.msc, then press Enter or click OK.
2. When the Services window opens, locate the Bonjour service on the list and double click it.
3. Change the Startup type to Automatic (Delayed Start) and click Apply and OK to save the changes.

According to users, the Bonjour service can cause internet issues and the Unidentified network message to appear.

To fix this problem, you just need to change the startup type of the Bonjour service as shown above.

Several users reported that Id_String2.6844F930_1628_4223_B5CC_5BB94B87 9762 service can also cause this problem.

To fix the problem, simply locate the service, double-click it, and set its Startup Type to Disabled. After doing that, be sure to check if the issue is resolved.

21. Delete the 0.0.0.0 gateway

1. Click the Windows Start button, type cmd and select Run as administrator from the results to start Command Prompt with full privileges.
2. Now, type or paste the following command and press Enter to run it: route delete 0.0.0.0
3. After the command is executed, restart your PC and check if the problem is resolved.

Several users reported that the issue is caused by the 0.0.0.0 gateway courtesy of Adobe CS3 Bonjour, but you can fix the issue simply by removing the gateway.

22. Change the Power Management settings for your adapter

1. Open the Network Connections window by right-clicking the Start icon and selecting the option from the menu.
2. Click on Wi-Fi from the left, then scroll down on the right and select Change adapter options.
3. Locate your wireless connection, right-click it and choose Properties from the menu.
4. Click on the Configure button.
5. Now navigate to the Power Management tab and uncheck Allow the computer to turn off this device to save power. Click OK to save changes.
6. Right click the wireless adapter again and choose Properties.
7. Go to the Sharing tab and uncheck Allow other network users to connect through this computer’s Internet connection option. Click OK to save changes.

If you’re getting the Unidentified network message while using a Wi-Fi network, you might be able to solve it by using this method.

According to users, you can fix this problem with ease simply by changing Power Management settings of your adapter.

After making the aforementioned changes, the problem should be completely resolved.

23. Change your Roaming Sensitivity

1. Right-click the Windows Start button and choose Network Connections from the menu.
2. Click on Wi-Fi from the left pane, then scroll down on the right and select Change adapter options from Related settings.
3. Find your wireless connection, right-click it and select Properties.
4. Hit the Configure button.
5. Navigate to the Advanced tab, locate Roaming Sensitivity or Roaming Aggressiveness (depending on your system) on the list and select it, then adjust values until the problem is resolved.

A few users reported that you can fix the problem simply by disabling Roaming Sensitivity, so be sure to try that as well.

24. Change your router’s encryption

Wi-Fi networks usually use encryption in order to prevent unauthorized access. Some of our readers reported that they fixed the problem simply by changing the network encryption on their router.

Users reported issues while using WPA2 encryption, but after changing it to WPA, the issue was resolved. To see how to change the encryption type on your router, we advise you to check its instruction manual.

Usually, you will find the option in the Wi-Fi settings section under the Security section but that depends on your router brand, model, and software.

We also have a Wi-Fi and connectivity issues guide for Windows 10/11 that will further help you fix all kinds of connection problems so make sure to check it out.

25. Enter your MAC address manually

1. Click the Start button, type cmd and choose Run as administrator from the results to start Command Prompt with administrator privileges.
2. Type or paste the following command and press the Enter key to run it: ipconfig /all
3. Locate Physical Address of your adapter and write it down. The address will consist of six pairs of characters separated by dashes.
4. Now go to Network Connections window, right click your connection and choose Properties, then click the Configure button as shown in the previous solutions.
5. Go to the Advanced tab and select Network Address option from the list. Enter your MAC address in the Value field without any dashes. After you’re done, click OK button to save the changes.

If you’re getting the Unidentified network no Internet message, you might be able to fix it simply by entering your MAC address manually.

How do I fix Ethernet unidentified network in Windows 11?

Although it has some new features and design, Windows 11 is not all that different from Windows 10 and our readers have encountered all sorts of Internet connection problems in the new OS.

The Ethernet unidentified network and Unidentified network no Internet errors in Windows 11 are just as common because they are caused by the same problems.

Luckily, the similarities between the two systems will help you solve these problems by applying all the solutions we presented for Windows 10 above on the new OS.

There are, of course, a few differences. For instance, in Windows 11 is a lot easier to access the Advanced network settings from the Network & internet section in Settings.

However, should you require further information, check our guide on what you can do if you can’t connect to the network in Windows 11. It will help with Internet connectivity problems.

The Unidentified network message can prevent you from accessing the Internet, but you should be able to easily fix the problem by using some of our solutions listed above. We hope they helped!

If you switched to the new OS, we can also help you with a fix if the Windows 11 Ethernet is not working that will provide a lot more information.

Should you have more questions or suggestions for additional solutions, don’t hesitate to write us in the comments section below.

Чтобы обнаружить доступные для подключения сети, пользователю не нужно выполнять каких-либо дополнительные действия, так как Windows 10 превосходно делает это сама. Тем не менее, в силу различных причин с обнаружением и идентификацией сетей могут возникнуть проблемы. Одна из таких проблем заключается в невозможности определить сеть. При этом на иконке соединения в системном трее обычно появляется желтый восклицательный значок, а в разделе управления сетями и общим доступом вместо подключения обнаруживается некая неопознанная сеть.

Столкнуться с неполадкой пользователь может как после системного сбоя или установки стороннего программного обеспечения, так и без видимых на то причин. Но причины, конечно, имеются. К неисправностям с сетью приводят некорректное изменение настроек, удаление или повреждение отвечающих за сетевую конфигурацию файлов и ключей реестра, проблемы на стороне провайдера, неполадки с роутером и кабелем. Часто проблема носит временный характер, обусловленный «местным» сбоем в работе сетевого адаптера. Поговорим обо всем более предметно.

Разовый сбой в работе оборудования

Проблемы с подключением, в том числе, с неопознанной сетью без доступа к интернету иногда возникают в результате локальных сбоев оборудования – сетевого адаптера и роутера. В таких случаях помогает обычная перезагрузка компьютера и, если этого оказывается недостаточно, маршрутизатора. Кстати, на данном этапе следует убедиться, что роутер раздает интернет на другие устройства, таким образом, вы исключите его из списка «подозреваемых». Перезагрузить оборудование, однако, следует в любом случае.

Некорректная работа VPN

Бывает и такое, что Windows 10 пишет «неопознанная сеть» при неудачном подключении к VPN. Если вы пользуетесь услугами туннелирования, попробуйте отключить VPN-клиент и его службу либо изменить параметры подключения. После деактивации службы клиента желательно перезагрузить компьютер.

Сбой настроек TCP/IP

Изменение сетевых настроек сторонней программой или самим пользователем – еще одна довольно таки распространенная причина описанной выше неполадки. Избавиться от сообщения «неопознанная сеть» в Windows 10 можно путем установки правильных настроек и/или сброса параметров подключения. Для того, чтобы сбросить сетевые настройки в «десятке», зайдите в Параметры – Сеть и Интернет и воспользуйтесь опцией «Сброс сети» в разделе «Состояние». Альтернативный вариант – выполнить в запущенной с повышенными привилегиями консоли три команды, а именно netsh int ip reset, ipconfig /release и ipconfig /renew.

Еще одно решение – задать в настройках проблемного адаптера автоматическое получение адреса. Командой ncpa.cpl откройте список ваших сетей, зайдите в свойства неопознанной сети (адаптера) и найдите пункт «Протокол Интернета версии 4 (TCP/IPv4)». Выделив его мышкой, откройте свойства и измените настройки так, как показано на приложенном ниже скриншоте. Это уместно сделать, если там уже были какие-то настройки, которые, кстати, необходимо записать, так как они еще вам могут пригодиться.

В ряде случаях, если подключение осуществляется через роутер, помогает использование статических IP-адресов. Обычно используются адреса 192.168.1.1 или 192.168.0.1, а вообще нужно смотреть на корпусе вашего маршрутизатора. При этом последнюю цифру айпишника следует заменить на произвольную (но не для основного шлюза). Не помешает также попробовать установить другой DNS, использовать который можно и при автоматическом получении IP. Наиболее популярный DNS от Google, к примеру, имеет адреса 8.8.8.8 (предпочитаемый) и 8.8.4.4 (альтернативный).

Другие манипуляции с адаптером

Если ошибку «неопознанная сеть без доступа к интернету» в Windows 10 вышеприведенными способами устранить не получилось, попробуйте сменить MAC-адрес адаптера. Открываем командой devmgmt.msc Диспетчер устройств, находим там наш сетевой адаптер, заходим в его свойства, переключаемся на вкладку «Дополнительно» и ищем свойство «Сетевой адрес». Меняем его значение на произвольное число из 12 цифр, сохраняем настройки и перезагружаем компьютер.

Повреждение драйвера

Очень редко, но все же иногда имеют место быть проблемы с сетевым ПО. Однако не спешите качать и устанавливать новую версию драйвера. Попробуйте сначала через тот же Диспетчер устройств удалить старый сетевой драйвер и перезагрузить ПК, чтобы он смог заново инсталлироваться в Windows. И только если это не поможет, обновите драйвер.

Итог

Это были основные причины неполадок, приводящих к появлению надписи «Неопознанная сеть». Как исправить ошибку, мы в общем-то рассмотрели. Остается лишь добавить, что столкнувшимся с данной проблемой пользователям не помешает проверить работу антивируса и брандмауэра, а также программ для мониторинга соединения, если таковые используются.

При подключении к Интернету через WiFi или Ethernet в Windows 11/10/7 может появится ошибка Неопознанная сеть, без доступа к интернету или сети.

Ошибка неопознанной сети без доступа к интернету или сети обычно появляется из-за не правильной конфигурации IP-адресов, DNS, устаревших сетевых драйверов или сторонний антивирус блокирует соединение.

В данной инструкции разберем, как исправить ошибку, когда нет доступа к Интернету, но к сети подключается и сообщает, что она неопознанная.

Исправить неопознанную сеть без доступа к интернету и сети

1. Перезагрузить модем

Выключите компьютер или ноутбук, выключите модем и извлеките его с розетки. Подождите минуту и включите все обратно, после чего удостоверьтесь, пропала ли ошибка неопознанной сети без доступа к интернету.

2. Режим полета

В Windows 11/10 нажмите на центр действий панели задач и убедитесь, что Режим в самолете отключен.

3. Обновить сетевой драйвер

Нажмите сочетание кнопок Win+X и выберите Диспетчер устройств, после чего разверните графу Сетевые адаптеры. Если вы подключаетесь через WiFi, то это будет указывать на Wirelles адаптер. Если по проводу, то Conroller. Нажмите по сетевому адаптеру правой кнопкой мыши и выберите Обновить устройство.

В следующим окне нажмите на Автоматический поиск драйверов и следуйте рекомендациям на экране. Если драйвера не установятся, то придется зайти на официальный сайт и скачать сетевой драйвер. Это можно узнать по модели материнской плате ПК или по модели ноутбука.

4. Отключить виртуальные адаптеры

Все в том же диспетчере устройств, если у вас имеются виртуальные сетевые адаптеры, то отключите их все. Виртуальные адаптеры будут содержать слово «Virtual«.

5. Удалить скрытые ненужные устройства

В диспетчере устройств нажмите сверху на вкладку Вид и установите Показать скрытые устройства. Далее разверните пункт Сетевые адаптеры и удалите все полупрозрачные устройства, если они будут.

• Нажмите правой кнопкой мыши по полупрозрачному сетевому адаптеру и выберите Удалить устройство.

6. Отключить антивирус

Если вы используете сторонний антивирус, то рекомендую удалить его на время и проверить, устранена ли проблема с неопознанной сети и доступом к интернету. Именно удалить, так как при отключении, некоторые антивирусы продолжают работу брандмауэра, который и может блокировать сеть.

Кроме того, попробуйте отключить на время встроенный защитник Windows и его брандмауэр.

7. Отключить быстрый запуск

Нажмите сочетание кнопок Win+R и введите control.exe powercfg.cpl, после чего нажмите на Действие кнопок питания.

Нажмите сначала на Изменение параметров, которые сейчас недоступны, после чего снимите галочку ниже с пункта Включить быстрый запуск. Выключите ПК, подождите секунд 40 и включите, после чего проверьте, устранена ли проблема с неопознанной сетью и доступом к интернету.

8. Средства устранения неполадок сети

Нажмите Win+R и введите по прядку команды для запуска диагностики подключения к интернету, входящих подключений и сетевого адаптера.

• msdt.exe -id NetworkDiagnosticsWeb
• msdt.exe -id NetworkDiagnosticsInbound
• msdt.exe -id NetworkDiagnosticsNetworkAdapter

9. Сброс протоколов

Нажмите Win+X и выберите Терминал Windows (администратор) или запустите командную строку от имени админа. Введите по порядку следующие команды:

• ipconfig /release
• ipconfig /renew
• netsh winsock reset
• netsh int ip reset
• ipconfig /flushdns
• ipconfig /registerdns
• netsh int tcp set heuristics disabled
• netsh int tcp set global autotuninglevel=disabled
• netsh int tcp set global rss=enabled
• netsh int tcp show global

10. Изменить DSN сервера

Нажмите сочетание клавиш Win+R и введите ncpa.cpl, чтобы открыть сетевые подключения. Далее щелкните правой кнопкой мыши по WiFi или Ethernet адаптеру и выберите Свойства. Выделите одним нажатием IP версии 4 (TCP/IPv4) и ниже нажмите на кнопку Свойства. В новом окне установите значение на Использовать следующие адреса DNS-серверов и установите 1.1.1.1 — 1.0.0.1, после чего установите флажок на Подтвердить параметры при выходите и нажмите OK.

11. Изменить Duplex на Auto

Перейдите обратно в сетевые подключения нажав Win+R и введя ncpa.cpl. Щелкните правой кнопкой мыши по сетевому адаптеру, который выдает неопознанную сеть без доступа к интернету и выберите Свойства. Далее нажмите на кнопку Настроить, после чего в новом окне перейдите во вкладку Дополнительно. Найдите слово Duplex и справа установите значение на Auto.

[ Telegram | Поддержать ]